|

This
Full-Flow Manifold Filtration System is capable of processing Lube Oil or Hydraulic Oil at 1/2 Micron Nominal Particle
Retention, Water Removal or Media Treatment for Total Acid Number. It contains Differential Pressure Gages, Isolation Valves,
Air Eliminator Valves and Drain Valves. The system features
the ability of EHC to custom fit an array of Filtration Units for specific applications, such as, but not limited to: - Turbine Generator
Lube Oil Systems
- Boiler Feed Pump Turbines
- Ancillary Systems of all types
- Fluid Remediation of all types
This Multi-Element Filter Skid is utilized
on Ancillary Systems for Full-Flow Filtration at Ultra High Velocity Flow and provides 1/2 micron nominal particle retention.
This style Filtration System is available from 500 to 6,000 GPM. Each System is equipped with Differential Pressure Gages,
Air Eliminator/Blow Down Valve and Drain Valve, all mounted on a Forklift Base for easy movement within your plant.

This Filtration System is designed for
protecting the Hydrogen Seals on Generators from contamination. EHC Field Services, Inc. manufactures and installs these systems.
Contact EHC for details.
|

This
100% Stainless Steel, Skid Mounted Reservoir is purpose designed to enable the Ultra High Velocity Lube and Control Oil
Flushing of the following Ancilliary and Non-Adequate Fluid Capacity Systems: - STG & GTG EHC SYSTEMS
- STG &
GTG SEAL OIL SYSTEMS
- STG LUBE OIL COOLER SYSTEMS
- STG BOILER FEED PUMP TURBINE LUBE OIL SYSTEMS
- STG & GTG LUBE OIL STORAGE AND TRANSFER SYSTEMS
- GTG
AIR COOLED LUBE OIL COOLER SYSTEMS
- FUEL OIL SYSTEMS
When utilized with EHC Ultra High Velocity Flushing Skids, this System is second to none for efficiency.
|
|

These Filter Units remove contaminants that have been loosened and suspended by the High
Velocity Flow of the Lube Oil. The Units have 2" Inlet/Outlets and utilize a Size 1 Filter Bag. The Flush Operator
can visually monitor the loading of the Bags to determine the affect of the Flush Procedure.There are isolation valves on
the inlet and outlet as well as air elimination and drain valves.The Units are interconnected to the Flush System by SS
Flex Hose. Oil Samples are taken at the Sample Valve on each Vessel. Drip Pans are furnished as part of the Filtration
Configuration. Each Unit is mounted on a Secure Base.
|

The Heater Skid to the left of the Pump Skid is designed for Heating
the Lube Oil Reservoir Temperature during High Velocity Lube Oil Flushing Procedures. The High Velocity Pump has heating
capability due to friction. Higher temperature levels are achieved using this 60 KW Heater Skid.

Above and below are pictures of our E30X2718C
Portable Filtration System. This Unit is very valuable for the following tasks: - Reclamation of Lube and Hydraulic Fluids contained in Reservoirs while the system is
in operation or shutdown
- Filtered Transfer
of Fluid from storage tanks or delivery vehicles and drums into operating Reservoirs
- Versatile use of various filter media and micron retentions (Particulate, Water Absorbent,
Acid Treatment)
- 30 GPM Flow Rate
- Positive Displacement Pump
- Differential Pressure Gages (Inlet/Outlet)
- 1-1/2" Stainless Steel Suction and Discharge Hoses with Cam-lok Connectors
- Designed for single person movement and operation

|
|
|

EHC Heater Units have evolved over the past
35 years to an extremely efficient machine that provides controlled heat to Lube Oil Reservoirs of 500 to 20,000 Gallon Capacity.
This Unit (shown before assembly of elements and our proprietary control system) has the versatility to provide
16 KW, 32 KW, 48 KW or 64 KW heating capacity from one skid, thermostatically controlled with redundant "Fail
Safe" devices. The electricals are 480V, 3 Phase, 60 Cycle and 120 Amps at full load.
|
|
|